Discover the Bassline Toothpick Drone
Introducing the uniquely designed Bassline Toothpick Drone, inspired by team pilot Nathan Loopz. With its roots going back to 2019, this 2inch Micro FPV toothpick drone boasts outstanding performance in the micro freestyle category. Equipped with a powerful X12 5-IN-1 AIO flight controller, the Bassline ensures an extraordinary flying experience like no other.
Noteworthy Features
With an inbuilt 2.4G ELRS V2.0 and OPENVTX VTX Power up to 400mw, the Bassline provides stable and secure flight performance. The drone also supports ELRS V3.0 with a firmware upgrade. The powerful EX1103 KV11000 motors and CaddxFPV Ant FPV camera guarantee a sharp flying session. For optimal performance, we recommend using 2S batteries with a width of roughly 17mm and a height of about 13mm (not included).
Elevating Specifications
The Bassline Toothpick Drone boasts a lightweight design with a wheelbase of 90mm and a size of 115mm*115mm*40mm. The optional receiver versions include 2.4G ELRS SPI, SPI Frsky D8/D16, SPI Flysky, and PNP (without an onboard receiver). Among the spare parts specifications, you can find detailed information on the motor, propellers, flight controller, onboard 4in1 ESC, onboard SPI ExpressLRS 2.4GHz, onboard SPI Frsky D8/D16, onboard SPI Flysky receiver version, PNP version (without onboard receiver), onboard 5.8g OPENVTX, and the Caddx ANT 1200tvl camera.
What's Included
When you purchase the Bassline Toothpick Drone, the package includes the Bassline 2inch frame and canopy, X12 ELRS V2.1 flight controller with built-in SPI ELRS 2.4G receiver (optional versions available), EX1103 KV11000 brushless motors, Gemfan toothpick 2023 tri-blade propellers (4cw+4ccw), Caddx ANT 1200TVL Camera, onboard 5.8G Openvtx 0mw~400mw VTX, and a canopy for a 14mmx14mm camera.
Get ready to experience unparalleled flight performance with the Bassline Toothpick Drone!
Product Specifications
|
Motor
|
Mode: EX1103 KV11000
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm
Weight(g):3.8g
No.of Cells(Lipo):1-2S
|
|
Propellers
|
Weight:0.88g
Material: PC
Pitch:2.3inch
Props Dia:52.17mm
Center Thickness:5mm
Center Hole Dia:1.5mm
|
|
Flight controller
|
X12 ELRS V2.1 flight
controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
X12 Frsky V2.1 flight
controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
X12 Flysky V1.0 flight
controller built-in SPI Flysky 2.4G receiver Target: CRAZYBEEF4FS
X12 PNP V1.1 flight controller
without onboard receiver Target:
CRAZYBEEF4DX
MCU:STM32F411CEU6 (100MHZ,
512K FLASH)
Sensor: ICM20689 or ICM42688P(SPI connection)
Mount hole size: 25.5mm*25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI
Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
|
|
Onboard 4in1 ESC
|
Power supply: 1-2S LiPo/LiPo
HV
Current: 12A continuous peak 15A
(3 seconds)
Support BLHeliSuite programmable
Default Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
|
|
Onboard SPI ExpressLRS 2.4GHz
Receiver
|
Packet Rate option:
50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Compatible with ExpressLRS V2.0 TX
Module
Couldn’t flash separately
ExpressLRS firmware
Could flash FC firmware to support ExpressLRS v3.0 TX
module
|
|
Onboard SPI Frsky
D8/D16 receiver Version
|
SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8/D16 model Channels: 8ch/16ch
No ground interference ( Transmitter and receiver 1 m from the ground): 200meter Failsafe support |
|
Onboard SPI Flysky
receiver Version
|
SPI BUS receiver
Protocol: AFHDS-2A
Channels: 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground):
200meter
Failsafe support |
|
PNP Version
(without onboard
receiver)
|
Full UART1 for external Receiver Support CRSF/GHOST/SBUS/IBUS/DSMX
protocol IR1 pad(invert RX1) used for SBUS input |
|
Onboard 5.8g OPENVTX
|
Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw)
|
|
Caddx ANT 1200tvl
camera
|
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: 0.001Lux@F1.2 Auto Gain Control: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V Weight: 2g (N.W.) |
|
Item Name
|
Qty
|
|
Bassline 2inch frame and
canopy
|
1
|
|
Option1: X12 ELRS V2.1 flight controller built-in SPI ELRS
2.4G receiver
|
1
|
|
Option2: X12 Frsky V2.1 flight controller built-in SPI Frsky
2.4G receiver
|
|
Option3: X12 Flysky V1.0 flight controller built-in SPI Flysky
2.4G receiver
|
|
Option4: X12 PNP V1.1 flight controller without onboard
receiver
|
|
EX1103 KV11000 brushless motor
|
4
|
|
Gemfan toothpick 2023 tri-blade
propellers(4cw+4ccw)
|
1
|
|
Caddx ANT 1200TVL Camera
|
1
|
|
Onboard 5.8G Openvtx 0mw~400mw
VTX
|
1
|
|
Canopy for 14mmx14mm camera
|
1
|
Product Images
